产品信息: CORONA 日冠 M610 兼容睿思凯 16通道接收机 mini 16ch 穿越机固定翼SBUS
 [打印本页]  [关闭本页]

产品编号: COR-M610 产品品牌:
产品名称: CORONA 日冠 M610 兼容睿思凯 16通道接收机 mini 16ch 穿越机固定翼SBUS 产品重量:
产品类别: 遥控/2.4G模块/接收 产品尺寸:

特征:

日冠M610  2.4GHz接收机(D8制式兼容)说明书

简介:

 日冠M610  D16制式兼容接收机适用于老版本Frsky D16协议的发射源,例如:Jumper T-LITE, T16, T18, Radiomaster TX12, TX16s,  FrSky模组: DFT, DJT, DHT, XJT, XJT_lite .

规格:

尺寸:          20x13x3mm

工作电流:     最大60mA

工作电压范围:  3.5V-10.0V

距离:          最大1.5km

重量:          2g

SBUS通道速率:  9ms

特点:

1SBUS通道输出

可设置的低压警报和回传信号警报

对码:

 先打开发射源并进入对码模式,然后按住F/S按钮的同时给接收机接通电源(不要连接任何其他外设)。接收机绿色LED灯常亮,然后遥控器蜂鸣器开始发出beebee声,接着接收机红色LED灯开始闪烁则表示接收机对码完成。关闭遥控器和接收机,然后再次给遥控器和接收机通电,此时绿色LED灯常亮表示接收机正在接收遥控器指令。

 失效保护设置:

 本系列兼容接收机支持在接收机上设置失控保护,打开遥控器给接收机通电,在接收机和遥控器连接上的前30秒内,用户可以通过如下按键操作将此时遥控器的通道数据保存在接收机上(在设置失控保护的时候不建议连接其他外设)。在设置完成后我们建议给接收机稳定供电。

   重新对码后失控保护会失效

LED灯状态定义:

RED

GREEN

Indication

常亮

熄灭

无信号

熄灭

常亮

信号很好

闪烁

常亮

信号正常

闪烁

闪烁

信号弱

距离检查:

 我们建议用户在使用新绑定的接收机飞行前做一次距离检查。

 


技术参数:

M610Compatible Receiver Manual

Introduction:

       Corona M610 D16 compatible receiver isavailable for any TX that use the old version Frsky D16 protocol, such asJumper T-LITE, T16, T18,  RadiomasterTX12, TX16s, etc and the FrSky two way telemetry modules: DFT, DJT, DHT, XJT,XJT_lite, etc.

 

Specifications:

Dimension: 20x13x3mm

Weight: 2g

Operating Voltage Range: 3.5V-10.0V

Operating Current: Max 60mA

Operating Range: Full range 1.5km

SBUS Frame Rate: 9ms

 

Features:

       One SBUS channel for special usage(connect FC or expand servo channel).

That canbe set the alarm warning on low voltage and return signal in the TX.

Bindprocedure:

First, turnon the TX and swicth to Bind mode. Second, power on the receiver whileholding the F/S button on the receiver (not connect any servo or other device) and you can see agreen LED going on steady on the receiver. And buzzer begins to sound beebee.The red LED on the receiver will flash, indicating the bind iscompleted. Turn off both the transmitter and the receiver. Turnon the transmitter and power on the receiver. The greenLED that going on steady on the receiver indicates that the receiver isreceiving commands from the transmitter.

 

FailsafeSetting:

    The compatible receivers support failsafe seton the receiver. Turn on the transmitter and power on the receiver. User canpress and release the F/S button as pictured and all channels data will berecorded by the receiver in the first 30s before receivers and TX are connected.When operating failsafe setting, it is not recommended that servos or otherdevices connect with the receiver. After completing failsafe setting, a stablepower supply to the receiver is recommended.

      Failsafe setting will be cancelled whenresetting the bind procedure

 

LEDStatus Indication

RED

GREEN

Indication

steady

off

No Signal

off

steady

Good Signal

flash

steady

Not Very Signal

flash

flash

Poor Signal


Rangecheck:

   We suggestuser do a range check before flying any new bind receiver.

 

 


附件:
包含:
1 x M610接收机

欢迎光临  模型总动员 (http://www.mxzdy.com/)

模型总动员网 版权所有 © All Rights Reserved